7.5x9-inch cover with bleed on 4 sidesEnterasys Matrix® N37C103 ChassisHardware Installation GuideP/N 9033824-06
viii 4. EXPORTRESTRICTIONS. YouunderstandthatEnterasysanditsAffiliatesaresubjecttoregulationbyagenciesoftheU.S.Government,including
ix8. AUDITRIGHTS. YouherebyacknowledgethattheintellectualpropertyrightsassociatedwiththeProgramareofcriticalvaluetoEnterasys,and,a
x
Contents xiContentsABOUT THIS GUIDEWho Should Use This Guide...
xii ContentsFigures1-1 The Matrix N3 7C103 Chassis with Redundant Power Supplies ... 1-22-1 7C203-1 Power Supply LEDs
About This Guide xiiiAbout This GuideThis guide lists features and options of the Enterasys Matrix® N3 7C103 chassis and explains how to install the p
Using the Enterasys Matrix Series Manual Setxiv About This GuideChapter 3, Chassis Setup, contains instructions for installing the chassis as a standa
Document ConventionsAbout This Guide xvDOCUMENT CONVENTIONSThis guide uses the following conventions:Note: Calls the reader’s attention to any item of
Document Conventionsxvi About This Guide
Introduction 1-11IntroductionThis chapter provides an overview of the Matrix N3 7C103 Chassis and its features. Also covered in this chapter are the i
Features1-2 IntroductionFigure 1-1 The Matrix N3 7C103 Chassis with Redundant Power Supplies1.2 FEATURESThe following provides an overview of the chas
FeaturesIntroduction 1-3Redundant Power SuppliesThe N3 chassis supports up to two 7C203-1 power supplies in the lower two slots of the chassis labeled
Features1-4 IntroductionPower Supply ReplacementTo reduce network downtime, a power supply may be removed after it has been powered down. When two pow
Getting HelpIntroduction 1-51.3 GETTING HELPFor additional support related to the N3 chassis or this document, contact Enterasys Networks using one of
Getting Help1-6 Introduction
Installation Requirements and Guidelines 2-12Installation Requirements and GuidelinesThis chapter describes the following:• Site guidelines that must
Configuration Guidelines2-2 Installation Requirements and Guidelines• Each 7C203-1 ac power supply requires a three-pronged power receptacle capable o
LANVIEW LEDsInstallation Requirements and Guidelines 2-32.3 LANVIEW LEDsThe following sections describe the LANVIEW® LED indications for the following
LANVIEW LEDs2-4 Installation Requirements and Guidelines2.3.2 Fan Status LEDRefer to Figure 2-2 for the location of the fan status LED. Table 2-2 desc
Chassis Setup 3-13Chassis SetupThis chapter contains instructions on setting up the N3 chassis.Equipment needed:• Phillips screwdriver• Flat blade scr
iNoticeEnterasys Networksreservestherighttomakechangesinspecificationsandotherinformationcontainedinthisdocumentanditswebsitewitho
Setting Up the Chassis3-2 Chassis Setup2. Remove the chassis from the protective plastic bag.3. Examine the chassis carefully and check for damage. If
Setting Up the ChassisChassis Setup 3-3To install the rubber feet, refer to Figure 3-1 and proceed as follows:1. Place the chassis on its back on a st
Setting Up the Chassis3-4 Chassis Setup3.2.3 Rack Mounting the ChassisWhen installing the N3 chassis into a standard 48.26-centimeter (19-inch) equipm
Setting Up the ChassisChassis Setup 3-5Figure 3-2 Rack Mounting the Chassis3.2.4 Attaching the Electrostatic Discharge Wrist StrapThe Electrostatic Di
Setting Up the Chassis3-6 Chassis Setup3.2.5 Installing a Power SupplyYou must install at least one 7C203-1 power supply into the N3 chassis. One powe
Setting Up the ChassisChassis Setup 3-7d. Secure the power supply to the chassis by using a screwdriver to tighten the two slotted screws on the front
Setting Up the Chassis3-8 Chassis SetupAfter completing the power supply and module installations, the chassis is ready to be powered up. Proceed to S
Setting Up the ChassisChassis Setup 3-9Figure 3-5 Removing a Power Supply from a Powered Up Chassis1 Power switch 4 AC power connector 7 N3 chassis2 A
Powering Up the Chassis3-10 Chassis Setup3.3 POWERING UP THE CHASSISTo power up the chassis, refer to Figure 3-6 and proceed as follows:1. Plug one en
Removing and Reinstalling the Fan TrayChassis Setup 3-116. Ensure that all fans in the fan tray unit are operating properly when power is received fro
ii Regulatory Compliance InformationFederal Communications Commission (FCC) NoticeThisdevicecomplieswithPart15oftheFCCrules.Operationissub
Removing and Reinstalling the Fan Tray3-12 Chassis SetupFigure 3-7 Removing the Fan Tray1 Fan tray 4 Captive screws2 7C103 chassis 5 Self-aligning ac
Removing and Reinstalling the Fan TrayChassis Setup 3-133.4.2 Reinstalling the Fan TrayTo reinstall the fan tray, refer back to Figure 3-7 and proceed
Removing and Reinstalling the Fan Tray3-14 Chassis Setup
Specifications and Regulatory Compliance A-1ASpecifications and Regulatory ComplianceThis appendix provides operating specifications for the Matrix N3
Power Supply RequirementsA-2 Specifications and Regulatory Compliance7C403 Fan TrayA.2 POWER SUPPLY REQUIREMENTS The requirements for the 7C203-1 ac p
Environmental RequirementsSpecifications and Regulatory Compliance A-3A.4 ENVIRONMENTAL REQUIREMENTSThe environmental requirements for the Matrix N3 7
Regulatory ComplianceA-4 Specifications and Regulatory Compliance
iiiElectromagnetic Compatibility (EMC)Thisproductcomplieswiththefollowing:47CFRParts2and15,CSAC108.8,2004/108/EC,EN55022,EN61000‐3‐2
iv ѻѻક䇈ᯢк䰘ӊSupplement to Product Instructions ᳝↦᳝ᆇ⠽䋼ܗ㋴(Hazardous Substance) 䚼ӊৡ⿄(Parts) 䪙3E∲+J䬝&G݁Ӌ䫀&U⒈㘨㣃3%%⒈Ѡ㣃䝮3%&apo
vVCCI NoticeThisisaclassAproductbasedonthestandardoftheVoluntaryControlCouncilforInterferencebyInformationTechnologyEquipment(VCC
vi Declaration of ConformityApplicationofCouncilDirective(s): 2004/108/EC2006/95/ECManufacturer’sName: Enterasys Networks, Inc.Manufacturer’sAddr
viiENTERASYS NETWORKS, INC. FIRMWARE LICENSE AGREEMENTBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,CAREFULLY READ THIS LICENSE AGREEMENT.Thisdocu
Comments to this Manuals