Enterasys Enterasys Matrix DFE-Gold Series Specifications download pdf (Page 107)

General Configuration Command Set

Setting Basic Device Properties

Matrix DFE-Gold Series Configuration Guide 2-81

2.2.3.32 set logout

Use this command to set the time (in minutes) an idle console or Telnet CLI session will remain

connected before timing out.

set logout timeout

Syntax Description

Command Defaults

None.

Command Type

Switch command.

Command Mode

Read-Write.

Example

This example shows how to set the system timeout to 10 minutes:

timeout Sets the number of minutes the system will remain idle

before timing out.

Matrix(rw)->set logout 10

1 2 ... 102 103 104 105 106 107 108 109 110 111 112 ... 127 128

Enterasys Matrix™ 1
DFE-Gold Series 1
ENTERASYS NETWORKS, INC 4
FIRMWARE LICENSE AGREEMENT 4
Contents 7
PORT CONFIGURATION 8
SNMP CONFIGURATION 9
SPANNING TREE CONFIGURATION 9
802.1Q VLAN CONFIGURATION 9
IGMP CONFIGURATION 10
IP CONFIGURATION 11
SECURITY CONFIGURATION 11
Contents 12
Ta bl e s 17
About This Guide 19
STRUCTURE OF THIS GUIDE 20
RELATED DOCUMENTS 21
DOCUMENT CONVENTIONS 22
Introduction 23
Matrix Series CLI Overview 24
1.3 DEVICE MANAGEMENT METHODS 25
1.4 GETTING HELP 25
Getting Help 26
Factory Default Settings 28
2.1.3 CLI Command Modes 34
2.1.4 Using WebView 35
• ro for Read-Only access 37
• rw for Read-Write access 37
Key Sequence Emacs Command 43
Key Sequence vi Command 44
2.1.7.1 show line-editor 46
2.1.7.2 set line-editor 47
Configuring the Line Editor 48
2.2.1.1 show system login 50
2.2.1.2 set system login 52
2.2.1.3 clear system login 53
2.2.1.4 set password 54
2.2.1.8 show system lockout 59
2.2.1.9 set system lockout 60
2.2.2.1 show mgmt-auth-notify 62
2.2.2.2 set mgmt-auth-notify 63
2.2.3.1 show ip address 69
2.2.3.2 set ip address 70
2.2.3.3 clear ip address 71
2.2.3.5 set ip gratuitous-arp 73
2.2.3.7 show system 75
2.2.3.8 show system hardware 77
2.2.3.12 show time 84
2.2.3.13 set time 85
2.2.3.14 show summertime 86
2.2.3.15 set summertime 87
2.2.3.16 set summertime date 88
Syntax Description 90
October 02:00 60 91
2.2.3.18 clear summertime 92
2.2.3.19 set prompt 93
2.2.3.20 set cli completion 94
2.2.3.21 loop 95
2.2.3.22 show banner motd 96
2.2.3.23 set banner motd 97
2.2.3.24 clear banner motd 98
2.2.3.25 show version 99
• Bp: BootPROM version 100
2.2.3.26 set system name 101
2.2.3.27 set system location 102
2.2.3.28 set system contact 103
2.2.3.29 set width 104
2.2.3.30 set length 105
2.2.3.31 show logout 106
2.2.3.32 set logout 107
2.2.3.33 show physical alias 108
2.2.3.34 set physical alias 110
2.2.3.35 clear physical alias 112
2.2.3.37 set physical assetid 114
2.2.4.1 set license 117
2.2.4.2 show license 118
2.2.4.3 clear license 119
Purpose 120
2.2.5.1 show inlinepower 122
2.2.5.2 set inlinepower mode 124
2.2.5.17 set port inlinepower 139
2.2.7.1 show boot system 145
2.2.7.2 set boot system 146
2.2.8.1 show telnet 148
2.2.8.2 set telnet 149
2.2.8.3 telnet 150
2.2.8.4 show router telnet 151
2.2.8.5 set router telnet 152
2.2.8.6 clear router telnet 153
2.2.9.1 dir 156
Table 2-8 dir Output Details 157
2.2.9.2 show file 159
2.2.9.3 show config 161
2.2.9.4 configure 163
2.2.9.5 copy 164
2.2.9.6 delete 166
2.2.9.7 script 167
2.2.10.1 show neighbors 170
2.2.10.2 show cdp 171
2.2.10.3 set cdp state 173
2.2.10.4 set cdp auth 174
2.2.10.5 set cdp interval 175
2.2.10.6 set cdp hold-time 176
2.2.10.7 clear cdp 177
2.2.10.8 show ciscodp 178
2.2.10.10 set ciscodp status 182
2.2.10.11 set ciscodp timer 183
2.2.10.13 set ciscodp port 185
2.2.10.14 clear ciscodp 188
2.2.11.1 show mtu 191
2.2.11.2 set mtu 192
2.2.11.3 clear mtu 193
2.2.12.1 cls (clear screen) 195
2.2.12.2 exit 196
2.2.13 Resetting the Device 197
2.2.13.1 show reset 198
2.2.13.2 reset 199
2.2.13.3 reset at 200
2.2.13.4 reset in 201
2.2.13.5 clear config 202
2.2.14.1 show support 204
2.3.2.1 show router 209
2.3.2.2 set router 210
2.3.2.3 clear router 211
2.3.2.4 router 212
• Set system 213
• Save/copy 213
and the 214
Port Configuration 217
Port Configuration Summary 218
3.3.1.1 show console 223
3.3.1.2 clear console 224
3.3.1.3 show console baud 225
3.3.1.4 set console baud 226
3.3.1.5 clear console baud 227
3.3.1.9 show console bits 231
3.3.1.10 set console bits 232
3.3.1.11 clear console bits 233
3.3.1.13 set console stopbits 235
3.3.1.15 show console parity 237
3.3.1.16 set console parity 238
3.3.1.17 clear console parity 239
3.3.2 Reviewing Port Status 240
3.3.2.1 show port 241
3.3.2.2 show port status 242
3.3.2.3 show port counters 244
Reviewing Port Status 247
3.3.3.1 set port disable 251
3.3.3.2 set port enable 252
3.3.3.3 show port alias 253
3.3.3.4 set port alias 254
3.3.3.5 show forcelinkdown 255
3.3.3.6 set forcelinkdown 256
3.3.3.7 clear forcelinkdown 257
3.3.4.1 show port speed 259
3.3.4.2 set port speed 260
3.3.4.3 show port duplex 261
3.3.4.4 set port duplex 262
3.3.5.1 show port jumbo 264
3.3.5.2 set port jumbo 265
3.3.5.3 clear port jumbo 266
3.3.6.1 show port negotiation 268
3.3.6.2 set port negotiation 269
3.3.6.3 show port mdix 270
3.3.6.4 set port mdix 271
3.3.6.5 clear port mdix 272
3.3.6.6 show port advertise 273
3.3.6.7 set port advertise 275
Command Mode 276
Read-Write 276
3.3.6.8 clear port advertise 277
3.3.7 Setting Flow Control 279
3.3.7.1 show port flowcontrol 280
3.3.7.2 set port flowcontrol 282
3.3.8.1 show port trap 284
3.3.8.2 set port trap 285
3.3.8.3 show linkflap 286
3.3.8.5 set linkflap 291
3.3.8.6 set linkflap interval 292
3.3.8.7 set linkflap action 293
3.3.8.8 clear linkflap action 294
3.3.8.11 clear linkflap down 297
3.3.8.12 clear linkflap 298
3.3.9.1 show port broadcast 300
3.3.9.2 set port broadcast 302
3.3.9.3 clear port broadcast 303
Overview: Port Mirroring 304
3.4.3.1 show port mirroring 305
3.4.3.2 set port mirroring 306
3.4.3.3 clear port mirroring 307
3.5.1 LACP Operation 309
3.5.2 LACP Terminology 310
(Section 3.5.4.13) 311
3.5.4.1 show lacp 313
3.5.4.2 set lacp 315
3.5.4.3 clear lacp state 316
3.5.4.4 set lacp asyspri 317
3.5.4.5 set lacp aadminkey 318
3.5.4.6 clear lacp 319
3.5.4.7 set lacp static 320
Configuring Link Aggregation 321
3.5.4.8 clear lacp static 322
3.5.4.10 set singleportlag 324
3.5.4.11 clear singleportlag 325
3.5.4.12 show port lacp 326
for port fe.1.12: 327
3.5.4.13 set port lacp 329
3.5.4.14 clear port lacp 332
SNMP Configuration 341
4.1.2 SNMPv3 342
SNMP Configuration Summary 343
4.3.1.1 show snmp engineid 346
4.3.1.2 show snmp counters 347
4.3.2.1 show snmp user 354
4.3.2.2 set snmp user 356
4.3.2.3 clear snmp user 357
4.3.2.4 show snmp group 358
4.3.2.5 set snmp group 360
4.3.2.6 clear snmp group 361
4.3.2.7 show snmp community 362
4.3.2.8 set snmp community 363
4.3.2.9 clear snmp community 365
4.3.3.1 show snmp access 367
4.3.3.2 set snmp access 370
4.3.3.3 clear snmp access 372
4.3.4.1 show snmp view 374
4.3.4.2 show snmp context 376
4.3.4.3 set snmp view 377
4.3.4.4 clear snmp view 378
4.3.5.2 set snmp targetparams 383
4.3.6.1 show snmp targetaddr 387
4.3.6.2 set snmp targetaddr 389
4.3.6.3 clear snmp targetaddr 391
4.3.7.1 show snmp notify 393
4.3.7.2 set snmp notify 395
4.3.7.3 clear snmp notify 396
About SNMP Notify Filters 397
4.3.7.5 set snmp notifyfilter 399
and associate a target 402
Spanning Tree Configuration 407
5.1.2 Spanning Tree Features 408
5.2.1.1 show spantree stats 413
5.2.1.2 show spantree version 416
5.2.1.3 set spantree version 417
5.2.1.5 show spantree stpmode 419
5.2.1.6 set spantree stpmode 420
5.2.1.12 set spantree msti 426
5.2.1.13 clear spantree msti 427
5.2.1.14 show spantree mstmap 428
5.2.1.15 set spantree mstmap 429
5.2.1.30 show spantree hello 445
5.2.1.31 set spantree hello 446
5.2.1.32 clear spantree hello 447
5.2.1.33 show spantree maxage 448
5.2.1.34 set spantree maxage 449
Legacy Path Cost is disabled 457
Tx hold count = 3 463
5.2.1.52 set spantree maxhops 467
5.2.1.75 show spantree debug 490
5.2.1.76 clear spantree debug 492
5.2.2.11 set spantree portpri 505
Section 5.2.1.28 507
Section 5.2.1.43 511
802.1Q VLAN Configuration 521
• show vlan (Section 6.3.1.1) 523
6.3.1.1 show vlan 524
6.3.2.1 set vlan 527
6.3.2.2 set vlan name 528
6.3.2.3 clear vlan 529
6.3.2.4 clear vlan name 530
6.3.3.1 show port vlan 533
6.3.3.2 set port vlan 534
6.3.3.3 clear port vlan 536
6.3.3.4 show vlan interface 537
6.3.3.5 set vlan interface 538
6.3.3.6 clear vlan interface 539
6.3.3.9 show port discard 542
6.3.3.10 set port discard 543
6.3.3.11 clear port discard 544
6.3.4.1 show port egress 546
6.3.4.2 set vlan egress 547
6.3.4.3 clear vlan egress 549
1H152-51 554
6.3.6.1 show gvrp 556
6.3.6.2 show garp timer 558
6.3.6.3 set gvrp 560
6.3.6.4 clear gvrp 561
6.3.6.5 set garp timer 562
6.3.6.6 clear garp timer 564
Configuring Policy Profiles 566
7.3.1.1 show policy profile 567
7.3.1.2 set policy profile 569
7.3.1.3 clear policy profile 571
7.3.1.4 show policy invalid 572
7.3.2.1 show policy rule 576
7.3.2.3 set policy classify 582
7.3.2.4 set policy rule 584
7.3.2.5 clear policy rule 588
7.3.2.7 set policy port 591
7.3.3.1 show cos state 600
7.3.3.2 set cos state 601
7.3.3.3 show cos port-type 602
7.3.3.4 show cos unit 605
7.3.3.5 show cos port-config 606
7.3.3.15 show cos reference 622
7.3.3.20 show cos settings 628
7.3.3.21 set cos settings 629
7.3.3.22 clear cos settings 630
Configuration 635
Configuring Port Priority 636
8.3.1.1 show port priority 637
8.3.1.2 set port priority 638
8.3.1.3 clear port priority 639
• 100Base-T - 4 643
• 1000Base-T - 4 643
• 1000Base-X - 8 643
8.3.3.1 show port ratelimit 646
8.3.3.2 set port ratelimit 648
8.3.3.3 clear port ratelimit 650
IGMP Configuration 651
IGMP Configuration Summary 652
9.4.1.1 show igmp enable 654
9.4.1.2 set igmp enable 655
9.4.1.3 set igmp disable 656
9.4.2 Configuring IGMP 657
9.4.2.1 show igmp query 658
9.4.2.2 set igmp query-enable 659
Configuring IGMP 660
IGMP group table is full 661
9.4.2.6 show igmp config 663
9.4.2.7 set igmp config 665
9.4.2.8 set igmp delete 667
9.4.2.9 show igmp groups 668
9.4.2.10 show igmp static 669
9.4.2.11 set igmp add-static 670
9.4.2.13 show igmp protocols 672
9.4.2.14 set igmp protocols 673
9.4.2.15 clear igmp protocols 674
9.4.2.16 show igmp vlan 675
9.4.2.17 show igmp reporters 676
9.4.2.18 show igmp flow 677
9.4.2.19 show igmp counters 678
Chapter 11 681
10.2.1.1 show logging all 683
10.2.1.2 show logging server 686
10.2.1.3 set logging server 687
Configuring System Logging 688
10.2.1.4 clear logging server 689
10.2.1.5 show logging default 690
10.2.1.6 set logging default 691
Table 10-3 693
Mnemonic Application 697
10.2.1.11 show logging local 700
10.2.1.12 set logging local 701
10.2.1.13 clear logging local 702
10.2.1.14 set logging here 703
10.2.1.15 clear logging here 704
10.2.1.16 show logging buffer 705
10.2.2.1 history 707
10.2.2.2 show history 708
10.2.2.3 set history 709
10.2.2.4 show netstat 710
10.2.2.5 ping 712
10.2.2.6 show users 714
10.2.2.7 tell 715
10.2.2.8 disconnect 716
10.2.3 Configuring SMON 717
10.2.3.1 show smon priority 718
10.2.3.2 set smon priority 719
10.2.3.3 clear smon priority 720
10.2.3.4 show smon vlan 721
10.2.3.5 set smon vlan 722
10.2.3.6 clear smon vlan 723
10.2.4 Configuring RMON 724
Configuring RMON 725
10.2.4.1 show rmon stats 728
10.2.4.2 set rmon stats 731
10.2.4.3 clear rmon stats 732
10.2.4.4 show rmon history 733
10.2.4.5 set rmon history 735
10.2.4.6 clear rmon history 736
10.2.4.7 show rmon alarm 737
10.2.4.10 clear rmon alarm 742
10.2.4.11 show rmon event 743
SNMP trap, both, or none 744
10.2.4.14 clear rmon event 748
10.2.4.15 show rmon host 749
Example 750
10.2.4.18 clear rmon host 753
10.2.4.19 show rmon topN 754
10.2.4.22 clear rmon topN 759
10.2.4.23 show rmon matrix 760
10.2.4.26 clear rmon matrix 764
10.2.4.27 show rmon channel 765
10.2.4.28 set rmon channel 766
“capture all” 767
10.2.4.29 clear rmon channel 768
10.2.4.30 show rmon filter 769
10.2.4.31 set rmon filter 770
10.2.4.32 clear rmon filter 772
10.2.4.33 show rmon capture 773
10.2.4.34 set rmon capture 775
10.2.4.35 clear rmon capture 777
10.2.5.1 show arp 779
10.2.5.2 set arp 780
10.2.5.3 clear arp 781
10.2.5.4 show rad 782
10.2.5.5 set rad 783
10.2.5.6 show ip route 784
10.2.5.7 traceroute 786
10.2.5.8 set ip route 789
10.2.5.9 clear ip route 790
10.2.5.10 show port mac 791
10.2.5.11 show mac 792
10.2.5.12 set mac 794
10.2.5.13 clear mac 795
10.2.5.14 show newaddrtraps 797
10.2.5.15 set newaddrtraps 798
10.2.5.16 show movedaddrtrap 799
10.2.5.17 set movedaddrtrap 800
10.2.6.1 show sntp 802
10.2.6.2 set sntp client 804
10.2.6.3 clear sntp client 805
10.2.6.4 set sntp server 806
10.2.6.5 clear sntp server 807
10.2.6.10 set sntp poll-retry 812
10.2.6.14 show timezone 816
10.2.6.15 set timezone 817
10.2.6.16 clear timezone 818
10.2.7.1 show nodealias 820
10.2.7.2 show nodealias mac 822
Configuring Node Aliases 824
10.2.7.5 set nodealias 828
10.2.7.7 clear nodealias 830
10.2.8 Configuring NetFlow 832
10.2.8.1 show netflow 833
10.2.8.2 set netflow 835
10.2.8.3 clear netflow 836
IP Configuration 837
IP Configuration Command Set 838
11.2.1.1 show interface 840
11.2.1.2 interface 842
11.2.1.4 show ip interface 844
11.2.1.5 ip address 846
11.2.1.6 no shutdown 847
11.2.2.1 show running-config 849
11.2.2.2 write 850
11.2.2.3 no ip routing 852
11.2.4.1 show ip arp 856
11.2.4.2 arp 858
11.2.4.3 ip gratuitous-arp 859
11.2.4.5 ip proxy-arp 861
11.2.4.6 ip mac-address 862
11.2.4.7 arp timeout 863
11.2.4.8 clear arp-cache 864
11.2.5.2 ip forward-protocol 867
About DHCP/BOOTP Relay 868
11.2.5.3 ip helper-address 869
11.2.6.1 show ip protocols 872
11.2.6.2 show ip traffic 873
11.2.6.3 clear ip stats 875
11.2.6.4 show ip route 876
11.2.6.5 ip route 878
11.2.6.6 ip icmp 880
11.2.6.7 ping 881
11.2.6.8 traceroute 882
11.2.7 Configuring PIM 883
11.2.7.1 ip pim sparse mode 884
11.2.7.2 ip pim bsr-candidate 885
Configuring PIM 886
11.2.7.3 ip pim dr-priority 887
11.2.7.4 ip pim rp-address 888
11.2.7.5 ip pim rp-candidate 889
11.2.7.6 show ip pim bsr 890
11.2.7.8 show ip pim neighbor 894
11.2.7.9 show ip pim rp 896
11.2.7.10 show ip pim rp-hash 898
11.2.7.11 show ip mroute 899
11.2.7.12 show ip mforward 901
About LSNAT 902
Session Persistence 903
Task Use these commands 905
NOTE: These commands must be 907
11.2.8.2 ip slb ftpctrlport 909
11.2.8.3 ip slb serverfarm 910
11.2.8.4 real 911
11.2.8.5 predictor 912
11.2.8.6 sticky 913
11.2.8.7 show ip slb reals 914
11.2.8.10 maxconns 920
11.2.8.11 weight 921
11.2.8.13 ip slb vserver 925
11.2.8.14 serverfarm 926
11.2.8.15 virtual 927
11.2.8.17 client 930
11.2.8.18 persistence level 931
11.2.8.19 allow accessservers 933
11.2.8.21 show ip slb conns 936
11.2.8.22 show ip slb stats 938
11.2.8.23 show ip slb sticky 939
11.2.8.24 clear ip slb 940
11.2.8.25 show router limits 941
11.2.8.26 set router limits 942
11.2.8.27 clear router limits 944
DHCP Overview 945
Configuring DHCP 945
DHCP Task List 946
DHCP Command Modes 946
11.2.9.1 ip dhcp server 949
11.2.9.2 ip local pool 950
11.2.9.3 exclude 951
11.2.9.4 ip dhcp ping packets 952
11.2.9.5 ip dhcp ping timeout 953
11.2.9.6 ip dhcp pool 954
11.2.9.7 domain-name 955
11.2.9.8 dns-server 956
11.2.9.9 netbios-name-server 957
11.2.9.10 netbios-node-type 958
11.2.9.11 default-router 959
11.2.9.12 bootfile 960
11.2.9.13 next-server 961
11.2.9.14 option 962
11.2.9.15 lease 964
11.2.9.16 host 965
11.2.9.17 client-class 966
11.2.9.18 client-identifier 967
11.2.9.19 client-name 968
11.2.9.20 hardware-address 969
12.2.2 Configuring RIP 976
12.2.2.1 router rip 978
12.2.2.2 network 979
12.2.2.3 neighbor 980
12.2.2.4 distance 981
12.2.2.5 ip rip offset 983
12.2.2.6 timers 984
12.2.2.7 ip rip send version 985
About RIP Authentication 987
12.2.2.9 key chain 988
12.2.2.10 key 989
12.2.2.11 key-string 990
12.2.2.12 accept-lifetime 991
12.2.2.13 send-lifetime 993
12.2.2.16 no auto-summary 997
12.2.2.19 passive-interface 1000
12.2.2.20 receive-interface 1001
12.2.2.21 distribute-list 1002
12.2.2.22 redistribute 1003
Configuring RIP 1004
12.2.3 Configuring OSPF 1005
Configuring OSPF 1006
12.2.3.1 router ospf 1008
12.2.3.2 network 1009
12.2.3.3 router id 1010
12.2.3.4 ip ospf cost 1011
12.2.3.5 ip ospf priority 1012
12.2.3.6 timers spf 1013
12.2.3.13 distance ospf 1020
Command Defaults 1021
12.2.3.14 area range 1022
12.2.3.15 area authentication 1023
12.2.3.16 area stub 1024
12.2.3.17 area default cost 1025
12.2.3.18 area nssa 1026
12.2.3.19 area virtual-link 1027
12.2.3.20 passive-interface 1029
12.2.3.21 redistribute 1030
12.2.3.22 database-overflow 1032
12.2.3.23 show ip ospf 1034
Output What It Displays 1038
Output What It Displays 1041
12.2.3.30 debug ip ospf 1048
12.2.3.31 rfc1583compatible 1049
12.2.4 Configuring DVMRP 1050
Commands 1050
12.2.4.1 ip dvmrp 1051
12.2.4.2 ip dvmrp metric 1052
12.2.4.3 show ip dvmrp route 1053
12.2.5 Configuring IRDP 1055
12.2.5.1 ip irdp 1056
Configuring IRDP 1057
12.2.5.4 ip irdp holdtime 1059
12.2.5.5 ip irdp preference 1060
12.2.5.6 ip irdp address 1061
12.2.5.7 no ip irdp multicast 1062
12.2.5.8 show ip irdp 1063
12.2.6 Configuring VRRP 1064
12.2.6.1 router vrrp 1065
12.2.6.2 create 1066
12.2.6.3 address 1067
12.2.6.4 priority 1069
12.2.6.5 master-icmp-reply 1070
12.2.6.6 advertise-interval 1071
Configuring VRRP 1072
12.2.6.7 critical-ip 1073
VLAN 1, VRID 1: 1074
12.2.6.8 preempt 1075
12.2.6.9 preempt-delay 1076
12.2.6.10 enable 1078
12.2.6.13 show ip vrrp 1081
Security Configuration 1083
Overview of Security Methods 1084
Policy Profile Assignment 1085
Filter-ID Attribute Formats 1085
• TACACS+ 1089
• RADIUS 1089
13.3.2 Configuring RADIUS 1090
13.3.2.1 show radius 1092
13.3.2.2 set radius 1094
13.3.2.3 clear radius 1096
Configuring RADIUS 1097
• IP address 1099
13.3.3 Configuring RFC 3580 1102
About RFC 3580 1102
Configuring RFC 3580 1104
13.3.4 Configuring TACACS+ 1106
13.3.4.1 show tacacs 1107
13.3.4.2 set tacacs 1110
13.3.4.3 clear tacacs 1112
13.3.5.1 show dot1x 1115
Examples 1116
13.3.5.3 set dot1x 1120
About PWA 1125
• forward ARP requests 1126
13.3.6.1 show pwa 1128
13.3.6.2 set pwa 1131
13.3.6.3 set pwa hostname 1132
13.3.6.4 clear pwa hostname 1133
13.3.6.5 show pwa banner 1134
13.3.6.6 set pwa banner 1135
13.3.6.7 clear pwa banner 1136
13.3.6.8 set pwa displaylogo 1137
13.3.6.9 set pwa redirecttime 1138
13.3.6.10 set pwa ipaddress 1139
13.3.6.11 set pwa protocol 1140
13.3.6.13 set pwa guestname 1142
13.3.6.14 clear pwa guestname 1143
13.3.6.16 set pwa gueststatus 1145
13.3.6.17 set pwa initialize 1146
13.3.6.18 set pwa quietperiod 1147
13.3.6.19 set pwa maxrequests 1148
13.3.6.20 set pwa portcontrol 1149
13.3.6.21 show pwa session 1151
About CEP Phone Detection 1175
13.3.8.1 show cep connections 1177
13.3.8.2 show cep detection 1178
13.3.8.3 show cep policy 1179
13.3.8.4 show cep port 1180
13.3.8.5 set cep 1181
13.3.8.6 set cep port 1182
13.3.8.7 set cep policy 1183
• Both UDP and TCP 1187
13.3.8.13 set cep initialize 1189
13.3.8.14 clear cep 1190
parameters 1191
13.3.9.1 show maclock 1193
13.3.9.3 set maclock enable 1197
13.3.9.4 set maclock disable 1198
13.3.9.5 set maclock 1199
Configuring MAC Locking 1200
13.3.9.7 set maclock move 1201
13.3.9.9 set maclock static 1203
13.3.9.11 set maclock trap 1205
13.3.9.12 clear maclock 1206
About Multiple Authentication 1207
13.3.10.1 set multiauth mode 1209
precedence: 1212
13.3.10.5 show multiauth port 1213
13.3.10.6 set multiauth port 1214
13.3.11.1 show ssh state 1226
13.3.11.2 set ssh 1227
13.3.11.3 set ssh hostkey 1228
13.3.11.4 show router ssh 1229
13.3.11.5 set router ssh 1230
13.3.11.6 clear router ssh 1231
13.3.12.1 show access-lists 1233
Configuring Access Lists 1234
ip access-group command 1234
* Advanced License Required * 1237
13.3.12.4 ip access-group 1242
About Policy-Based Routing 1243
13.3.13.1 show route-map 1245
13.3.13.2 route-map 1246
13.3.13.3 match ip address 1248
13.3.13.4 set next hop 1249
13.3.13.5 show ip policy 1250
13.3.13.6 ip policy route-map 1252
13.3.13.7 ip policy priority 1253
13.3.13.9 ip policy pinger 1255
13.3.14.1 show hostdos 1257
13.3.14.2 hostdos 1258
About FST 1261
13.3.15.1 show flowlimit 1263
13.3.15.2 set flowlimit 1264
13.3.15.3 set flowlimit limit 1265
• user port 1267
• server port 1267
• aggregation port 1267
• inter-switch link 1267
• unspecified port 1267
• interswitch link 1271
13.3.15.8 set flowlimit port 1273
Numerics 1281

Comments to this Manuals

No comments

Enterasys Enterasys Matrix DFE-Gold Series Specifications Page 107

Comments to this Manuals

Related products and manuals for Network switches Enterasys Enterasys Matrix DFE-Gold Series